电动扳手检验试验及保养
Inspection, test and maintenance of electric wrench
1电动扳手的金属外壳应可靠接地，其外壳应有定期检验试验合格证，并在有效期限内。
1 The metal shell of the electric wrench shall be reliably grounded, and its shell shall have the certificate of regular inspection and test, which shall be within the validity period.
2检查电动扳手机身安装螺钉紧固情况，若发现螺钉松了，应立即重新扭紧，否则会导致电动扳手故障。
2 Check the fastening of the mounting screws on the body of the electric wrench. If the screws are loose, they should be retightened immediately, otherwise the electric wrench will fail.
3检查手持电动扳手两侧手柄完好，不开裂可破损，安装牢固。
3 Check that the handles on both sides of the hand-held electric wrench are intact, not cracked or damaged, and firmly installed.

电动扳手使用和操作注意事项
Precautions for use and operation of electric wrench
1、确认现场所接电源与电动扳手铭牌是否相符。是否接有漏电保护器。
1. Confirm whether the on-site power supply is consistent with the nameplate of the electric wrench. Whether leakage protector is connected.
2、根据螺帽大小选择匹配的套筒，并妥善安装。
2. Select the matching sleeve according to the size of the nut and install it properly.
3、在送电前确认电动扳手上开关断开状态，否则插头插入电源插座时电动扳手将出其不意地立刻转动，从而可能招致人员伤害危险。
3. Before power transmission, confirm that the switch on the electric wrench is disconnected, otherwise the electric wrench will turn immediately when the plug is inserted into the power socket, which may cause personal injury.
4、若作业场所在远离电源的地点，需延伸线缆时，应使用容量足够，安装合格的延伸线缆。延伸线缆如通过人行过道应高架或做好防止线缆被碾压损坏的措施。
4. If the work place is far away from the power supply, the extension cable with sufficient capacity shall be used and qualified extension cable shall be installed. If the extension cable passes through the sidewalk, it shall be elevated or measures shall be taken to prevent the cable from being damaged by rolling.
5、尽可能在使用时找好反向力距支靠点，以防反作用力伤人。
5. Try to find the support point of the reverse force distance when using it to prevent the reaction force from injuring people.
6、使用时发现电动机碳火花异常时，应立即停止工作，进行检查处理，排除故障。此外碳刷必须保持清洁干净。
6. If abnormal carbon sparks are found in the motor during use, the motor shall be stopped immediately for inspection and troubleshooting. In addition, the carbon brush must be kept clean.
7、站在梯子上工作或高处作业应做好高处坠落措施，梯子应有地面人员扶持。
7. Measures for falling from high places shall be taken when working on ladders or working at heights, and ladders shall be supported by ground personnel.
以上就是为大家介绍的有关扭剪螺栓专用扳手详细的介绍,希望对您有所帮助.如果您有什么疑问的话,欢迎联系我们.我们将以的态度,为您提供服务
The above is a detailed introduction to the special wrench for torsional shear bolts, and we hope it will be helpful to you. If you have any questions, please contact us. We will provide services for you with our attitude