服务热线: 400-117-8816
           13406879330

扭剪扳手,扭剪螺栓专用扳手,扭剪电动扳手,扭剪枪生产厂家

当前位置:首页>技术文献高强螺栓扭剪扳手操作注意事项

高强螺栓扭剪扳手操作注意事项

来源:日期:2024-06-19 发布人:创始人

强螺栓扭剪扳手是拆卸指纹件及螺帽的机器化施工机器,存正在主动掌握扭矩性能。

The strong bolt torque wrench is a mechanized construction machine that disassembles fingerprint parts and nuts, and actively controls torque performance.

扭剪扳手宽泛使用于栓焊构造桥梁的架构,厂房、塔架及化工、冶金、火力发电设施的装置。重型机器、起重设施和车辆拆卸工作,以及对于螺纹紧固件的扭矩及轴向张力有

Twisted shear wrenches are widely used in the construction of bridge structures, factories, towers, and equipment for chemical, metallurgical, and thermal power generation facilities. Heavy machinery, lifting facilities, and vehicle dismantling work, as well as torque and axial tension for threaded fasteners

a41a6172-68f8-4907-94b6-d4013d124fc7

严厉要求的场所。接下来我们来看看扭剪扳手的操作注意事项:

A place with strict requirements. Next, let's take a look at the precautions for operating a torsion wrench:

1、接回电源前应先检查电源电压能否与本货物铭牌符合,能否有接地安装。当电源电压超过+ 10%时应采取稳压措施,要不会反应掌握精密度。接地没有良易形成事变。

1. Before reconnecting the power supply, it is necessary to check whether the voltage of the power supply matches the nameplate of the goods and whether there is grounding installation. When the power supply voltage exceeds+10%, voltage stabilization measures should be taken to ensure precision is not compromised. Grounding is not conducive to accidents.

2、机器运用的条件量度为-10°C-40°C,过高过低都会反应掌握精密度。

2. The condition measurement for machine operation is -10 ° C-40 ° C, and whether it is too high or too low will reflect the mastery of precision.

3、机器用来组装螺帽时,其扭矩没有得大于额外扭矩值。正常状况下,没有是本拉手拧紧的或者锈蚀重大的螺帽,没有宜用本拉手组装,免得形成机器保护。

3. When the machine is used to assemble nuts, its torque does not exceed the additional torque value. Under normal circumstances, there are no nuts that are tightened or heavily rusted by this handle, and it is not advisable to assemble them with this handle to avoid forming machine protection.

4、变换旋转位置时,必需待发电机中止转动后停止,严禁正在运行中扳动正反电门。

4. When changing the rotation position, it is necessary to wait until the generator stops rotating, and it is strictly prohibited to turn the front and back switches while in operation.

5、当拉手主动中止后即可抓紧电门待4-5秒后再停止开行拉手,要不拉手不能发动。

5. After the handle is actively stopped, you can grab the switch and wait for 4-5 seconds before stopping the operation of the handle, otherwise the handle cannot be started.